Taoist Car Repair Beam Calibrator You How To Use Modified Vehicles – Car Repair, Beam Correction –

car modify
by MSVG

Body Correction is by some external force will be accident damage or repair of fatigue damage to the vehicle location technology standard factory “state” process. For the “state”, which contains two meanings. “Like” is more intuitive look and shape of the “state” is a more abstract concept of a deeper level, such as metal in accordance with the internal molecular structure will re-order the original location, the internal stress is completely released, etc. it is directly related to the function after the repair of vehicles and life. Structural equipment means the body in the car plays a major role in supporting and bearing components, is the installed base of body parts, common rails, beams, door-post and beam and other parts below. Such structures typically have very high strength, combined with structural mostly closed box section, it must be taken in the repair of the means and measures, use of reasonable repair process.

Related Reading: Teach you how to use the modified vehicle beam calibrator Yantai Power Development

lion latest calibration equipment, medium and large vans frame

Tutorials how to repair the vehicle beam calibrator

Repair process in place as far as possible

Integral body correction should take place as far as possible repair methods. So that when pulled, can effectively part of the way around some of deformation “belt” out, but also because fewer components and save a lot of disassembly time. Figure 1a is a damaged front bar frame, the components for the closed box-section beam, which is connected by screws and front rails together. Typically, a lot of sheet metal Service Technicians will remove the frame after the correction, it is unscientific. Skeleton in the front bar by the impact, the impact force will cause the transmission of the front longitudinal deformation. After removing the fixed frame is not difficult to take appropriate corrective force of a moderate repair, while repair after complete skeleton on the front rail also need repair. Therefore, a better approach is to place repair, use the pull with a pair of impact deformation position to exert a force to ease the opposite direction, and then use a suitable pry bar, from the edge of an opening into it on the side of some of the skeleton Depression sites were repaired, it will get very good results.

, Of course, for non-load-type body structure parts often can be repaired using this method in place. Non-bearing-type body that is the traditional beam-type body and its frame is a separate component, usually thicker material, is “U” shaped steel or two “U” formed steel welded box reverse component, which has very high intensity. Usually can be divided into border-style ladder frame chassis and other types of bolts and the body through together. By the impact of such distortion in the frame, the usual repair method is to Drive Separate room and cargo compartment of the frame were removed after the correction. In fact, such a frame even after the removal of these components is difficult to have a good anchor method, so for some injury types of distortion can use the method of Figure 2a in place repair. Frame in the lateral bending produced by the impact can be an adequate strength of I-beam (rail steel) on the side of the vehicle, using the horse stool or wood to pad to the frame level with the use of chain the I-beam front and rear parts and the frame fixed, bend the top part of the hydraulic thrust of the method applied correction.

The same time, the method can be used to repair Figure 2b. Most cases this will bend the frame of a beam position from there, resulting in deformation of the beam at the same time. Once both sides of the beam bending in the middle did not occur when the beams should be used to separate hydraulic roof support on both sides of the bent part, to the original width, so that it can be used when applied thrust beams facilitates the transfer to another force side, easy to repair both sides simultaneously. For the upper and lower bending beams can also use this method, when corrected beam directly on the lower part of I-beam and using the same method can be repaired. However, correction should be as much as possible so that I-beam and the frame close to, in order to obtain a stable correction of force, use of chain and girders should be fixed with a suitable piece of wood or iron to prevent deformation.

I am China Bags Wholesale writer, reports some information about infant winter boots , soft leather infant shoes.

Expert Analysis: Vehicle Modification Of Four Common Elements – Conversion – Automotive Repair And

In fact, there is no fixed model car modification, so long as to be able to change according to their own imagination, to install on it. This is a culture, a spirit, a kind of enjoyment, but also an understanding of the car. In the conversion process, the owner can understand the basic performance of the car, control car and engine areas more knowledge. Related Reading: Germany, the latest modified Ferrari EDO Enzo [Photos] Increase the Sport Kit Lorinser Mercedes-Benz SL sports car modification (Photos)

Modified car are three factors: the economic strength of the owner, modification and automotive parts supply annual evaluation system. Many people have started working to their own Car Installation of new tricks, but still rare in professional internal alterations. Conversion means that cost is too specialized, small Market And low adaptability.

Converted vehicles in two ways: wearing new clothes, law and law in lamb’s clothing. In Car body Posted many good signs for the new car is like wearing the same impressive fashion, this is “The Emperor’s New Clothes”; now pop a “wolf dressed in sheep’s clothing” modification approach, the car’s engine, high-performance driving system improvements, and look a bit fixed. The event of the same model car, can immediately show the performance difference.

High flow air filter: Engine air filter is to filter the air required to operate the engine in the petrol engines have this device, in the eyes of play vehicles, the original car’s air filter is installed into the gas shortage may have suspected . Therefore, people have modified intake system to play car practice.

A lot of people think that high-volume air filters provide high-speed operation of the engine when the air flow rate is different, in fact, this view is not very accurate. Because the size of gas into the intake will not be modified to change devices, as long as the engine displacement does not change, air flow rate will not change unless the use of turbochargers. The principle is that the engine using vacuum Deputy pressure, so that outside air into the cylinder itself, but because the air through the filter into the cylinder, so the resistance of the air can not enter the same pressure to the outside world, and because the air is inertia, Therefore, modified air filter is a crucial step. Modified by the actual test engine running at high speed, Power Increase the engine running smoothly, speed feels good.

Expert opinion Install high flow air filter as far as possible away from the engine. Airflow into the engine temperature as low as possible, only low temperature can have a high density; the same time, the oxygen content also increased slightly.

If no suitable space around the engine installation, you can take with partitions separating the engine and filters.

Ordinary air filter modified with different prices for different models in between 350-800 yuan float. 10,000 km to 30,000 km need cleaning or replacement, maintenance or replacement price.

I am an expert from China Bags Wholesale, usually analyzes all kind of industries situation, such as oil radiator heater , oil radiant heater.

Wheel and tire upgrade the technical requirements modification – tires, wheels, conversion – Automotive repair and maintenance industry

Big shiny wheels, wide tires exaggerated, exciting life “people” shaped tire tread, these are all of the most powerful car parts keep returning, of course, the most important vehicle parts. Several years ago, car stickers and bumper stickers were another “big siege” are considered to be modified in different age, and car modification industry in Beijing quietly grow, the owner of their cognitive level of constantly improving, the real conversion gradually been accepted, including tire and wheel upgrade is converted fans the focus of concern, both in visual effect, or function, the tire wheel is the most direct.

General competitive flat tires used less than in 50, and are single-oriented patterns of tires, good drainage properties, grip is not bad, a few years ago the popular Beijing Goodyear’s F1 series is part this type of tires, and F1 has a huge cool “people” shaped pattern, a classic at that time. Now have more choices, Yokohama’s A539 series, Michelin’s PilotSport series, BFGoodrich’s a gForceSport series, etc., recently the rise of a non-symmetrical pattern of the tire, the middle of this pattern is oriented around both sides of the groove side of the drainage, the side of the grip, especially on rainy days when the results are very good corners.

Whole tire upgrade is simply to consider three aspects:

First: The upgraded tires and the original tire size should not vary too much, you must meet certain safety standards.

Second: pick a tire for true to their pattern, not the blind pursuit of beauty.

No. 3: Be sure to see the origin of the tire, do not select a number of so-called parallel imports.

Upgrade tires there are many misunderstandings:

First: that the tire wheel can be infinitely greater. Generally speaking, the current car tire manufacturers configuration is more reasonable, taking into account comfort, safety and power, small-displacement engines, such as the 1.6L car unless the following were generally not very strong driving force for refitting and conversion The total original tire diameter 3 cm or more difference in the tires, or at worst increase in fuel consumption and speed up the weak, while in the direction of home to play dead when Cengdao the inner wheel arch, and even lead to abnormal tire wear and positioning inaccurate. Here is one formula for calculating the total diameter:

Total diameter = tire diameter wheel (inches) * 2.54 + flat tire width * ratio * 2

Such as tires for the 185/60-14 tire overall diameter = 14 × 2.54 +18.5 * 0.6 * 2 = 57.76 cm, you can dress up for the 195/50-15 tires (total diameter of 57.6 cm).

Second: Only choose a pattern that the more complex the pattern, the better grip. What patterns are in fact not “bald” tires is the best grip on dry ground tires, tire contact area, the strongest grip. However, the wetlands that are the most dangerous tires, rain tires to use this, as in skating, as brakes and steering will be null and void. In rainy areas, select the tire tread must drain of good. Select the best way to tire tread tires consulting professional conversion stores.

Third: select a number of parallel imports cheaper plan. Foreign tire manufacturers to produce some of the surplus or defective products are cheap smuggled to China, these products are authentic quality with a difference of more. Best tire brands to choose their place of origin of production of tires, do not select a small country of production of OEM products.

Tire choice right, following the selection of a beautiful wheel, and nice wheels add much color to make your car, you can also get matching larger brake discs and brake calipers. But please pay attention to selecting the most important condition is the hub of the wheel hub modified to meet original factory specifications Hub

The e-commerce company in China offers quality products such as PDH Multiplexer , china Optical Ethernet Switch, and more. For more , please visit TDM over IP today!